|
-High
Performance, Cost-effective 16-bit with CAN
|
|
SBC
MODULE FEATURES
- SBC
in subminiature dimensions (60 x 53 mm) according to low EMI phyCORE
specifications
- populated
with various 144-pin C167Cx and ST10 family 16-bit microcontroller
- -Infineon
C167CR controller with on-chip Full CAN 2.0B
- -Infineon
C167CS controller with dual on-chip Full CAN 2.0B
- -STMicro
ST10F168 controller with 256 KB on-chip Flash
- controller
and board-level signals extend to two 100-pin high-density (0.635mm)
Molex connectors on underside of the SBC
- on-board
memory:
- -SRAM:
256KB to 1MB
- -Flash:
256KB to 2MB
- -Serial:
4 to 32KB EEPROM
- 16-bit
multiplexed mode
- 24-channel
A/D converter with 10-bit resolution if populated with the C167CS
(16-channel if populated with the ST10F168)
- battery-buffered
Real-Time Clock
- RS232
transceiver (optional second RS-232 transceiver)
- optional
UART support second asychronous serial interface (supporting all
modem signals)
- 2
x full 2.0B CAN bus interfaces via two 82C251 transceivers (1
x CAN interface if populated with ST10F168)
- MTBF=941,282
hours
|
 |
SBC
Module Description
The
phyCORE-167/ST10F168 supports high-end 16-bit controllers from Infineon
and ST Microelectronics featuring on-chip CAN and Flash. Smaller than
a credit card (60 x 53 mm), the standard board is populated with the Infineon
C167CR controller, runs at a 20MHz clock speed and offers a standard external
memory of 256 KB SRAM and 256 KB Flash. If populated with the ST10F168,
the module supports an additional 256 KB of on-chip Flash. PHYTEC FlashTools
enable easy on-board download of user code. All controller board-level
signals extend to two 100-pin high-density (0.635) Molex connectors aligning
two edges of the board. These pins provide a 16-bit bi-directional I/O
port, 64+ free port lines, a 24/16-channel ADC with 10-bit resolution
and one RS-232 interface (optional second RS-232). If populated with the
C167CS, two Full 2.0B CAN interfaces are available via P82C251 CAN transceivers.
The C167CR and ST10F168 support a single CAN interface.
|
Development
Board
Phytec
Development Boards are fully equipped with all mechanical and electrical
components necessary for the speedy and secure start-up and programming
of Phytec Single Board Computer modules:
- Development
Board in EURO-card dimensions (100 x 160 mm)
- 2x
DB-9 sockets for RS-232 interfaces
- 2x
DB-9 plugs for CAN interfaces
- 2x
opto-decoupled CAN transceivers
- PCM-997-VPP
if phyCORE-ST10F168 due to 12V Vpp for programming on-chip Flash
- Expansion
Bus enabling connectivity to Add-on hardware
|
|
Rapid
Development Kit
Phytec
Rapid Development Kits provide all necessary ingredients with which
to jump start embedded designs and propel concept to prototype and
finished product:
- phyCORE-167/ST10
Single Board Computer module
- phyCORE
development Board HD-200 (PCM-997-V2, PCM-997-VPP if phyCORE-ST10F168
due to 12V Vpp for programming on-chip Flash)
- serial
cable, AC adapter
- Phytec
Spectrum CD including SBC hardware manual, evaluation compiler,
software demos and Controller User's Manual
|
About
C167CR or C167CS or ST10F168>>>
|
