|
|
SBC
MODULE FEATURES
- Single
Board Computer in subminiature dimensions form factor (70 x 57
mm) according to low EMI phyCORE design
- Freescale
ColdFire MCF548x (200MHz) in a 388-pin BGA package
- Controller
and board-level signals extend to two high-density (0.635mm) 160-pin
Molex connectors on undersides of SBC
- on-board
memory
- -DDR
SDRAM: 64 to 128MB
- -Flash:
32 to 64 MB Intel Strata Flash, 32-bit memory width supporting
synchronous (K3) or asynchronous (J3) devices
- -Serial:
4 to 32 KB I2-EEPROM (alternatively I2C-FRAM, I2C-SRAM)
- 4xUART
ports (RXD/TXD/RTS/CTS RS-232 and 2x TTL-level interfaces)
- 2x
CAN ports, configurable as TTL-level
- 2x
10/100Mbit Ethernet ports
- 2.0
USB
- Lattice
ispXPLD 5000-family logic device
- PCI
2.2 bus, SPI bus, I2C bus, SSI (Synchronous Serial Interface)
with 2x /CS
- Real-Time
Clock with Calendar/Alarm
- 8
channel 12-bit ADC and 1 channel 12-bit DAC, both connected to
I2C bus
- JTAG/BDM
test/debug port
- industrial
temperature range (-40~+85C)
|
| |
SBC
Module Description
The
phyCORE-ColdFire/MCF548x supports the Freescale MCF548x ColdFire family,
which operates at a 200 MHz clock speed in industrial temperature range.
On-chip functional units include MMU, FPU, Cache, PCI and DDR SDRAM. The
module can be populated with up to 128 MB DDR SDRAM and 64MB Flash. Ethernet,
CAN, SPI, UART, USB2.0, I2C, processor bus, PCI bus and all applicable
processor signals are extend to the external Molex connectors. The on-board
user-programable logic device is an additional special feature of the
board, enabling load of processor firmware that can carry out specific
tasks during runtime. It is possible, for example, to initialize a 32KB
dual-port SRAM or FIFO to receive data from external peripheral units.
Functions such as Timer, Counter, CapComp, Decoder, Encoder, Demodulator,
additional Chip Select signals, special generated control signals and
fast I/O ports enable the module's wide range of use in embedded applications.
|
Development
Board
Phytec
Development Boards are fully equipped with all mechanical and electrical
components necessary for the speedy and secure start-up and programming
of Phytec Single Board Computer modules:
- Development
Board (125 x 160 mm) with PCI and CompactFlash expansion
- 5V
and 12V (PCI) voltage
- 2x
RS-232, 2x CAN interfaces
- BDM
interface with "Parallel-to-OCD" converter
- 3x
push buttons, 2x LEDs
- RJ-45
Ethernet interface
- BDM
interface
- Expansion
Bus for connectivity to Add-On hardware
|
|
Rapid
Development Kit
Phytec
Rapid Development Kits provide all necessary ingredients with which
to jump start embedded designs and propel concept to prototype and
finished product:
- phyCORE-ColdFire/MCF548x
Single Board Computer module (PCM-024)
- phyCORE-ColdFire/MCF548x
Development Board (PCM-982)
- serial
cable, parellel cable, AC adapter
- Phytec
Spectrum CD including SBC hardwares, manual, software, demos and
Controller User's Manual
- Metrowerks
CodeWarrior Evaluation Development Studio for ColdFire
- P&E
Microcomputer Systems ColdFire BDM interface Adapter
|
About
Freescale MCF548x>>>
|
