Chinese Version

phyCORE-MPC555
-32-bit PowerPC in Sub-mini Dimensions with Dual Full 2.0B CAN

SBC MODULE FEATURES

  • Single Board Computer in subminiature dimensions (72 x 57 mm) according to phyCORE low EMI specifications
  • Freescale's 32-bit MPC555 embedded controller (40MHz) in a 272-pin BGA package
  • controller and board-level signals extend to two high-density (0.635mm) 160-pin Molex connectors on underside of SBC
  • on-board memory:
  • -SRAM: 128KB to 8MB flow-through synchronous external burst SRAM (32-bit access, 0 wait states, 2-1-1-1 Burst Mode)
  • -Flash: 512KB to 4MB external Flash
  • -Serial: 4KB I2C EEPROM (optional 512 byte I2C FRAM)
  • I2C Real-Time clock with calendar and alarm functions
  • dual Full 2.0B CAN via PCA82C250 transceivers
  • SPI and dual UART with RS-232 level converters (optionally configurable as TTL level signals)
  • dual 16-channel A/D converters with 10-bit resolution
  • BDM debug interface
  • requires 5V/50mA and 3.3V/300~620 mA operating voltage
  • industrial temperature range (-40~85C)
  • MTBF=776,765 hours

SBC Module Description

The phyCORE-MPC555 is a cost-effective, high-performance Single Board Computer that packs the power of Freescale's embedded 32-bit PowerPC MPC555 microcontroller within a miniature footprint. All signals and ports of the MPC555 extend to two Molex high density (0.635 mm pitch) 160-pin header connectors, making the controller resources readily available to the developer. These high density pins allow the module to be plugged like a "big chip" into target hardware. The phyCORE-MPC555 can be populated with a maximum of 4 MB flow-through synchronous external BURST-SRAM for DATA storage and a maximum of 4 MB Flash memory at 0 wait states. The Flash serves as Boot and CODE memory and supports In-System programming. An additional 26 KB on-chip SRAM and 448 KB on-chip Flash memory are available on the MPC555. The 272-pin BGA controller also boasts a 64-bit Floating Point Unit, SPI, dual on-chip Full 2.0B CAN, dual-channel UART, and dual 16-channel A/D converters with 10-bit resolution.

Development Board

Phytec Development Boards are fully equipped with all mechanical and electrical components necessary for the speedy and secure start-up and programming of Phytec Single Board Computer modules:

  • Developent Board in EURO-card dimensions (100 x 160mm)
  • 5V and 3.3V voltage requlators accept unreg. input voltage in range from 7 to 12V
  • 2 x RS232, 2 x CAN interfaces
  • BDM interface with "Parallel-to-OCD" converter
  • 3 x push buttons, 2 x LEDs
  

Rapid Development Kit

Phytec Rapid Development Kits provide all necessary ingredients with which to jump start embedded designs and propel concept to prototype and finished product:

  • phyCORE-MPC555 Single Board Computer modules
  • phyCORE-MPC555 Development Board
  • serial cable, parallel cable, AC adapter
  • Phytec Spectrum CD including SBC hardware, manual, software, demos and Controller's Manual
  • Metrowerks CodeWarrior Evaluation Development Studio for PowerPC

About Freescale MPC555>>>

 

 The 10th Floor, Quantum Plaza, No. 27, Zhichun Road, Haidian District, Beijing, 100083, P.R. China
Tel: +86-10-82357579, 82357580, 82357576

Fax: +86-10-82357574
info@mcu-world.com